![]() But alas, there is no sound an no DTS indication on my receiver. dts file is playing and I can see the Spectrum Analyzer bargraph. Also, make sure that you system has a valid sound playback device and that it is properly configured in playback options."Īnd now it's getting rather interesting: when selecting the "ASIO4ALL v2" drivers instead of the "M-Audio ASIO Interface" in Outout Mode Settings, the two error messages above are gone. You can use DSP Studio to change the output to a compatible format. This output may not be supported by your hardware. (2) "Playback could not be started on the output 'ASIO using the format '32 bits Per Sample, 2 Channels'. (1) "The ASIO device 'M-audio USB ASIO Interface' does not support the sample rate of 44100Hz". wav files in combination with the M-Audio control-panel option "Dolby Digital/DTS pass-through 16-bit/48000Hz", MC12 pops up with the following dialog: 'System Volume' is selected in Player => Volume. I already assumed I have to somehow bypass the DirectShow filters. I assume the bitstream is handled by the M-Audio itself and send through SPDIF to my receiver, rather than passed-through and handled by the receiver itself which only works when playing DTS-DVDs. But there is no way I can use "pass-through" when playing. I setup ffdshow correctly (I guess) using glynor's Wiki DTSWAV article: DTS (and AC3) are set to SPDIF, DSP inside MC12 is disabled. I also found some related topics on this forum: and. I already tried ASIO4ALL as alternative driver in MC12, but nogo. Output though "pass-through" just sounds better. The output to the speakers is 5.1 and the receiver indicates DTS 3/2.1 output, BUT I noticed a quality difference between these two M-Audio control panel options mentioned above when playing DTS-DVD. img), the signal can only be played when selecting the "2-In/2-Out, 24-bit, 8000 – 48000 Hz" option in the M-Audio control panel. cue with.wav files) or loaded in a virtual drive (.ngc and. dts/.wav files, DTS-CD-images (on my hard disk as. The sound quality is absolutely stunning. When playing DTS-content from DVD in MC12 -such as Donald Fagen's Kamakiriad- the signal is passed-though correctly, using the "Dolby Digital/DTS pass-through 16-bit / 48000Hz" option in the M-Audio control panel and the ASIO playback setting in MC12 itself. I use ffdshow from the latest CCCP codec-pack. ![]() I connected a M-Audio Transit USB to my Sony DTS-receiver through optical SPDIF TOSlink. There is however a problem I cannot solve: ![]() The previous RGB effect which was configured with RGB Fusion 2 will be replaced with a static red color.I'm currently using the latest trial-version of MC12 and the software is just brilliant and on this extensive forum I already solved a lot of small playback issues and codec settings. When both software are running simultaneously, the selected RGB effect on the product will follow the last adjustment.įor example: When you attempt to set the LED effect to Static mode with a red color through the RGB Fusion in GCC. ![]() The two software can be installed and executed in the same environment at the same time.īoth RGB Fusion in GCC and RGB Fusion 2 can be used to control the RGB effects of supported products. RGB Fusion 2 : Can be downloaded directly from RGB Fusion 2 page or the products' page. RGB Fusion in GCC: Is available for download and install through Update Center when supported components are detected. For supported RGB products and motherboard models please refer to the RGB Fusion 2 support page. RGB Fusion 2: GIGABYTE's earlier RGB control software which is capable of running independently without dependence of other software. RGB Fusion in GCC: Includes newly designed UI with optimized RGB Sync methodology that comes with Gigabyte Control Center (GCC). ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |